Short answer

Selective plating deposits metal only on a defined area of a part instead of the whole surface. In production it is done by masking parts or plating strip in specialized lines. For repair, rework, prototypes and in-place work, selective brush plating does it with a pen-style tip and a DC power supply: no tank, no masking, and precious metal goes only where you put it.

Why plate selectively

  • Precious metal goes only on the functional surface, which cuts gold, silver and rhodium use
  • Parts can be plated in place without disassembly
  • No masking to apply and strip on one-off and low-volume jobs
  • Repairs a worn or damaged area without re-plating the whole part
  • Puts solderable tin on pads without touching the rest of the board

Selective plating methods compared

Common ways to plate selectively
MethodHow the area is controlledBest for
Masking + tankTape, lacquer or fixtures cover what should not plate; part goes in the bathProduction runs where the mask can be reused or automated
Production selective linesStrip or parts are plated to a set depth or zone on dedicated equipmentHigh-volume connectors and stamped contacts
Selective brush platingOnly the area under the plating tip receives metalRepair, rework, prototypes, field work, low volume

Selective brush plating with the Micro-Metallizer

The Micro-Metallizer is a selective brush plating system: a variable DC power supply, connector cables and self-contained plating pens. The pen tip defines the plated area, so there is nothing to mask on most jobs. Swap pens to run a full sequence on the same supply.

Connect the part to the negative (−) lead of the power supply and the pen to the positive (+) lead. Hold the pen so the whole tip touches the surface, and move it lightly back and forth in a slow stroke.

  1. 01

    Degrease the target area

    Absorbent / Degreaser pen at 10 to 12V, or the Stainless Steel Degreaser pen on stainless. Wipe clean.

  2. 02

    Underlayer

    Copper flash on steel, brass or zinc die-cast; nickel at 5 to 6V before gold, rhodium or palladium. Wipe clean between pens.

  3. 03

    Selective finish

    Plate the finish only where it is needed, at the pen's catalog voltage. More passes build more thickness.

  4. 04

    Wipe clean

    Wipe the plated area with a clean cloth.

Selective gold, tin, nickel and silver

  • Selective gold plating: connector pins, edge connectors, PCB gold fingers and switch contacts (Gold 24K, 18K, 14K and heavy-duty pens)
  • Selective tin plating: oxidized PCB pads and component leads that will not take solder (Tin pen, PL-1012)
  • Selective nickel plating: diffusion barrier under gold and base for rhodium and palladium (Nickel and Nickel Heavy Duty pens)
  • Selective silver plating: contacts and bus bar surfaces (Silver and Silver Heavy Duty pens)
  • Selective zinc plating: corrosion touch-up on plated steel (Zinc pen, PL-1013)

Thickness and coverage

Standard pens build 1.5 to 1.8 µm and heavy-duty pens build 3 to 3.6 µm. Each pen holds 10 ml of solution and covers roughly 300 square inches. For deposits much thicker than that, or for whole-part finishing at volume, a tank line is the better tool.

Typical deposit on a 1 in × 1 in copper surface, from the Micro-Metallizer catalog
Pen type2 minutes3 minutes
Gold0.5 µm0.8 µm
Palladium0.5 µm0.8 µm
Silver0.5 µm0.8 µm
Rhodium0.7 µm1.0 µm
Nickel0.4 µm0.6 µm
Black Nickel0.5 µm0.6 µm
Copper, Zinc, Tin, Chrome Color0.3 µm0.5 µm
Gold Heavy0.8 µm1.2 µm
Silver Heavy0.8 µm1.2 µm
Copper Heavy0.6 µm1.0 µm
Nickel Heavy0.8 µm1.2 µm

Frequently asked questions

What is selective plating?

Plating only a defined area of a part, such as a contact surface or solder pad, instead of the whole part.

Is selective plating the same as brush plating?

Brush plating is one form of selective plating. Selective plating can also be done by masking parts before tank plating or on dedicated production lines.

Do I need masking for selective brush plating?

Usually not. Metal deposits only where the pen tip touches.

What is selective gold plating used for?

Putting gold only on contact surfaces such as connector pins, edge connectors and PCB gold fingers, which saves gold and leaves the rest of the part as is.

What equipment do I need for selective plating?

For brush-style selective plating: a DC power supply, connector cables, a degreaser pen and the plating pens for your sequence. Micro-Metallizer kits with all of that start at $400.

Not sure which pens your part needs?

Tell us the substrate and the finish you need. Our team will tell you the sequence.

Related guides